The application spectrum reaches across all industries and comprises, for example:
The 1PH8 motors are suitable for installation in dry indoor areas without corrosive atmospheres.
SIMOTICS M-1PH8 motors, forced ventilation, shaft heights 80 to 160
SIMOTICS M-1PH8 motors, water cooling, shaft heights 80 to 160
SIMOTICS M-1PH8 motors, water cooling, shaft heights 180 to 280
SIMOTICS M-1PH8 motors, forced ventilation, shaft height 355
The SIMOTICS M-1PH8 motor series is a new motor generation for universal implementation in plants and machines that have been developed with Motion Control applications. The motors are available as an asynchronous variant as well as a compact synchronous variant with either forced ventilation or water cooling, based on a flexible building block principle. Comprehensive function expansions such as different bearing concepts expand the application range.
In comparison to the freely selectable performance of vector and servo control with the SINAMICS S120 drive system, it is possible to select between asynchronous or synchronous variants in the case of the 1PH8 motor series. This flexible interoperation of converter and motor makes it even easier to master extreme duty cycles, short control rise times and high precision in terms of speed, torque and positioning.
Because the 1PH8 motors are often used as the largest and central drive in the machine, they are known as "main motors".
Main motor = High performance + Highly dynamic response + High degree of protection
When developing the new 1PH8 motor series, we took special care to ensure maximum compatibility with the SINAMICS S120 drive system. For example, the specially harmonized power components, electronic rating plates, and the ability to integrate the motors via the DRIVE-CLiQ system interface ensure quick and easy commissioning as well as problem-free operation.
Typical speed/power characteristic for SIMOTICS M-1PH8 asynchronous motors
The characteristic curves show the typical relationship between motor speed and drive power for SIMOTICS M-1PH8 motors for duty type S1 (continuous duty) in accordance with IEC 60034-1.
The detailed characteristic curves for the corresponding voltage and winding variants can be found in the SIMOTICS M-1PH8 Configuration Manual..
SIMOTICS M-1PH8 motor forced ventilation/open-circuit cooling | |
---|---|
Insulation of the stator winding in accordance with EN 60034-1 (IEC 60034-1) | For an ambient temperature of up to 40 °C (104 °F) |
Cooling in accordance with EN 60034-6 (IEC 60034-6)
| Forced ventilation
|
Temperature monitoring | KTY temperature sensor in the stator winding 1PH818 ... 1PH835 additional KTY 84 as reserve |
Motor fan ratings | |
| 230 V 1 AC 50/60 Hz, 265 V 1 AC 60 Hz 400 V 3 AC 50/60 Hz, 480 V 3 AC 60 Hz 200 V ... 277 V 1 AC 50/60 Hz (EC fan) 400 V 3 AC 50/60 Hz, 480 V 3 AC 60 Hz |
Type of construction in accordance with EN 60034-7 (IEC 60034-7) | |
| IM B3, IM B5 IM B3, IM B5, IM B35 |
Degree of protection in accordance with EN 60034-5 (IEC 60034-5) | |
| IP55 IP23 |
Shaft extension on the drive end in accordance with DIN 748-3 (IEC 60034-5) | Plain shaft or feather key, full-key or half-key balancing for feather key |
Shaft and flange accuracy in accordance with DIN 42955 (IEC 60072-1) 1) | |
| Tolerance R (reduced) Tolerance N (normal) |
Vibration severity in accordance with Siemens/EN 60034-14 | |
| Grade R/A Grade A |
Sound pressure level LpA (1 m) in accordance with DIN EN ISO 1680, max. | |
Forced ventilation (IP55) | |
| 70 dB at a rated pulse frequency of 4 kHz and a speed range up to 5000 rpm |
| 73 dB at a rated pulse frequency of 4 kHz and a speed range up to 5000 rpm |
| 73 dB at a rated pulse frequency of 2 kHz and a speed range up to 5000 rpm |
| 73 dB at a rated pulse frequency of 2 kHz and a speed range up to 3500 rpm |
| 74 dB at a rated pulse frequency of 2 kHz and a speed range up to 3300 rpm |
| 77 dB at a rated pulse frequency of 2.5 kHz and a speed range up to 2800 rpm |
Open-circuit cooling (IP23) | |
| 73 dB at a rated pulse frequency of 2 kHz and a speed range up to 3000 rpm |
| 73 dB at a rated pulse frequency of 2 kHz and a speed range up to 2000 rpm |
| 74 dB at a rated pulse frequency of 2 kHz and a speed range up to 2800 rpm |
| 77 dB at a rated pulse frequency of 2.5 kHz and a speed range up to 2800 rpm |
Built-in encoder systems without DRIVE-CLiQ interface |
|
Built-in encoder systems with DRIVE-CLiQ interface |
|
Connection | Connector for signals or DRIVE-CLiQ-interface |
| Terminal box NDE top/power connector Terminal box top Terminal box NDE right |
Rating plate | 1 attached to motor 1 supplied separately with terminal box |
Paint finish | Standard paint finish in anthracite RAL 7016 |
Approvals, according to | cURus |
1) Shaft extension run-out, concentricity of centering ring and shaft, and perpendicularity of flange to shaft.
S/R = signals/revolution
SIMOTICS M-1PH8 motor water cooling | |
---|---|
Insulation of the stator winding in accordance with EN 60034-1 (IEC 60034-1) | For an cooling water inlet temperature of up to 30 °C (86 °F) |
Cooling in accordance with EN 60034-6 (IEC 60034-6) | Water cooling |
Temperature monitoring
| KTY temperature sensor in the stator winding 1 additional KTY84 as reserve |
Type of construction in accordance with EN 60034-7 (IEC 60034-7) | |
| IM B3, IM B5 IM B3, IM B5, IM B35 |
Degree of protection in accordance with EN 60034-5 (IEC 60034-5) | |
| IP65 IP55 |
Shaft extension on the drive end in accordance with DIN 748-3 (IEC 60034-5) | Plain shaft or feather key, full-key or half-key balancing for feather key |
Shaft and flange accuracy in accordance with DIN 42955 (IEC 60072-1) 1) | |
| Tolerance R (reduced) Tolerance N (normal) |
Vibration severity in accordance with Siemens/EN 60034-14 | |
| Grade R/A Grade A |
Sound pressure level LpA (1 m) in accordance with DIN EN ISO 1680, max. | |
| 68 dB at a rated pulse frequency of 4 kHz and a speed range up to 5000 rpm |
| 69 dB at a rated pulse frequency of 4 kHz and a speed range up to 5000 rpm |
| 70 dB at a rated pulse frequency of 2 kHz or 4 kHz and a speed range up to 5000 rpm |
| 70 dB at a rated pulse frequency of 2 kHz or 4 kHz and a speed range up to 4500 rpm |
| 72 dB at a rated pulse frequency of 2 kHz and a speed range up to 3300 rpm |
Built-in encoder systems without DRIVE-CLiQ interface |
|
Built-in encoder systems with DRIVE-CLiQ interface |
|
Connection | Connector for signals or DRIVE-CLiQ interface |
| Terminal box NDE top/power connector Terminal box top |
Paint finish | Standard paint finish in anthracite RAL 7016 |
Approvals, according to | cURus |
1) Shaft extension run-out, concentricity of centering ring and shaft, and perpendicularity of flange to shaft.
2) The following motors are designed to conform to temperature class 155 (F):1PH8107-1.F2/1PH8107-1.M21PH8138-2.F2/1PH8138-2.G21PH8164/1PH8166/1PH8168
Motor type | Fan motor current consumption, max. | Direction of air flow | Volume of air, min. | Sound pressure level Motor + external fan operation 50 Hz, | ||
---|---|---|---|---|---|---|
A | A | A | m3/s (ft3/s) | dB | ||
Forced ventilation | 230 V 1 AC/50 Hz (± 10 %) | 230 V 1 AC/60 Hz (± 10 %) | 265 V 1 AC/60 Hz (± 10 %) | |||
1PH808 | 0.33 | 0.25 | 0.32 | NDE → DE | 0.02 (0.71) | 70 1) |
Forced ventilation | 400 V 3 AC/50 Hz (± 10 %) | 400 V 3 AC/60 Hz (± 10 %) | 480 V 3 AC/60 Hz (± 10 %) | |||
1PH810 | 0.12 | 0.09 | 0.12 | NDE → DE | 0.04 (1.41) | 70 1) |
1PH813 | 0.13 | 0.16 | 0.17 | NDE → DE | 0.09 (3.18) | 70 1) |
1PH816 | 0.17 | 0.22 | 0.22 | NDE → DE | 0.16 (5.65) | 73 1) |
Forced ventilation (EC fan) | 200 V ... 277 V 1 AC/50 Hz, 60 Hz (± 10 %) | |||||
1PH818 | 1.45 ... 1.05 | – | – | NDE → DE | 0.17 (6.00) | 73 2) |
1PH822 | 2.3 ... 1.6 | – | – | NDE → DE | 0.31 (10.9) | 73 2) |
Forced ventilation | 400 V 3 AC/50 Hz (± 10 %) | 400 V 3 AC/60 Hz (+ 5 %, ± 10 %) | 480 V 3 AC/60 Hz (+ 5 %, – 10 %) | |||
1PH828 | 2.55 | 2.5 | 2.5 | NDE → DE | 0.31 (10.9) | 74 2) |
1PH835.-1..1 (IP55 degree of protection) | 4.7 | 4.6 | 4.6 | NDE → DE | 0.75 (26.5) | 77 3) |
1PH835.-1..4 | 4.7 | 4.6 | 4.6 | NDE → DE | 1 (35.3) | 77 3) |
1) For rated pulse frequency of 4 kHz and speed range up to 5000 rpm.
2) For rated pulse frequency of 2 kHz and speed ranges:
Forced ventilation (IP55 degree of protection): 1PH818 up to 5000 rpm 1PH822 up to 3500 rpm 1PH828 up to 3300 rpm
Forced ventilation (IP23 degree of protection): 1PH818 up to 3000 rpm 1PH822 up to 2000 rpm 1PH828 up to 2800 rpm
3) For rated pulse frequency of 2.5 kHz and speed range up to 2800 rpm.